鐵藝門是門類發展史上一個跨越式的進步，充滿藝術氣息的鐵藝把這別墅大門裝點得低調而又奢華，氣派十足！現在使用鐵藝門的人可謂是比比皆是。那么這關于鐵藝大門重要的三個問題，作為別墅業主的你就必須要了解一番了。
Iron gate is a leap forward progress in the history of the development of the category. The iron art full of artistic flavor decorates the villa gate with low-key and luxurious style! Now the use of iron gate can be said to be everywhere. Then, the three important issues about the iron gate, as the villa owner, you must understand.
現象一：鐵藝門門扇下降 -門鉸下墜，門扇、門框變形。
Phenomenon 1: the iron door leaves fall - hinge falls down, the door leaf and door frame are deformed.
原因：A、門鉸不夠力，虛位過大；B、門扇變形、凸起；C、門鉸受損大；
Causes: a. the hinge is not strong enough and the virtual position is too large; B. the door leaf is deformed and protruding; C. the hinge is damaged greatly;
解決方法：拆下鐵藝門門扇，調門鉸，門扇鉸往鎖方向敲打，門框鉸往鎖向相反方向敲打，3號暗鉸用內六角調節螺絲，一號暗鉸敲打其門框門鉸底座使之下沉，修復鐵藝門門扇、門框變形位置

Solution: remove the iron door leaf, adjust the hinge, knock the hinge to the lock direction, knock the door frame hinge to the opposite direction, use the internal hexagon adjusting screw for No. 3 concealed hinge, and knock the base of the door hinge with No. 1 concealed hinge to make it sink, and repair the deformation position of the iron door leaf and door frame
現象二：鐵藝門表面損傷：油漆脫落、損花 。
Second, the surface of the door is damaged.
原因：A、碰撞時出現損傷 B、腐蝕性損傷。
Causes: A. damage during collision; B. corrosive damage.
解決方法：用相同顏色進行修補油漆（注：小面積用毛筆劃畫，大面積用大排掃、注意毛掃與工件成30度角，油漆有能過多，不能用力，更好在紙板上先掃幾回，毛掃與壓花紋路的相反方向運行。
Solution: use the same color to repair the paint (Note: small area with brush, large area with large scan, pay attention to the brush and the workpiece to form a 30 degree angle, paint can be too much, can not be forced, it is best to brush several times on the cardboard, the brush and embossing lines run in the opposite direction.
現象三：鐵藝門門縫不均：左、右、上、下門縫不均
Phenomenon 3: uneven gap of iron gate: uneven gap of left, right, upper and lower doors
原因：A、鐵藝門門鉸邊上下鍵不均,B、上鍵左右不均勻。
Reasons: a. the upper and lower keys on the hinge edge of the iron door are uneven, and B. the upper key is uneven on the left and right.
解決方法：若上下縫不均（即橫縫），1、檢查門框?qū)蔷€(xiàn)；2、加減墊片，查看鐵藝門門扇鉸位上方間隙。
Solution: if the upper and lower seams are uneven (i.e. transverse joints), 1. Check the diagonal line of the door frame; 2. Add or subtract gaskets to check the clearance above the hinge position of the iron door leaf.